Refurbished Pellet Presses

If the press you need is not listed below please contact CFE at: www.info@cfegroup.com or call 0044 1942 728188

All Pellet Presses are Fully Refurbished to a High Standard, Run in at our Factory to Ensure we Deliver a High Quality Press to you  

 

In current condition
In current condition

Factory Refurbished CPM 3020-6 complete with:                                                                                                                                                                                                                                                                                         

                        132  KW Motor 1480 rpm

•          1 Complete set of roll assemblies

•          Manually operated die & roller hoist

        Force Feeder or Dump Chute

•          Manual Roll Adjustment 

•          Automatic greasing system

•          Sandblasted and painted 

       •          Die Size I/D 508 mm x 156 mm Working Width

Also available CPM conditioner & Geelen 14 x 14 single Deck Cooler                                                                                                                          

   

 

2001 Factory Refurbished CPM 7932-9, SN: 7932-9/5112/331 complete with:

 

·         250Kw1500 rpm motor

·         1 set roll assemblies

·         Manual roll adjustment

·         Dump chute

·         New Quill Flange and Die Clamps

·         New Shearpin Housing

·         New feed cone

·         New Stiffening Ring

·         New Front Roll Support Plate

·         New Door Liner

·         Manual die hoist

·         All New bearings & seals

·         Reservoir Greasing System

·         Sandblasted & painted 

·         Die size I/D825.5mm x track 240mm


 

 

 

Before Refurbishing
Before Refurbishing

Fully refurbished Matador M5 complete with:     

 

  • 22kw Motor 1500rpm
  • Feeder & Conditioner
  • 2 Complete set of roll assemblies (6)
  • Manual Roll Adjustment
  • Stainless steel door
  • Sandblasted and painted
  • New 6mm die & other part used dies
  • Electrical control panel
  • Set up for wood pelleting
 
 

 

Factory Refurbished CPM 3020-6 complete with:                                                       SOLD                                                                                                                                                                                                                                      

                        132  KW Motor 1480 rpm

•          1 Complete set of roll assemblies

•          Manually operated die & roller hoist

        Dump Chute

•          Manual Roll Adjustment 

•          Automatic greasing system

•          Sandblasted and painted 

      •          Die Size I/D 508 mm x 156 mm Working Width                                                                                                                              

   

 

Factory Refurbished Paladin 1600 (Choice of 2) Complete with:                                      ONLY 1 LEFT 

  • 2 x 110Kw 1500 rpm motors
  • Dump chute
  • 1 complete set roll assemblies
  • Choice of 2 or 3 roll machines
  • Manual roll adjustment
  • 50kgs Reservoir greasing system
  • Sandblasted and painted
  • Die size I/D 850 mm x 210 mm Working Width 

 

 

Factory Refurbished CPM 7800 Press complete with:                                                   

·                     185 KW Motor 1500 rpm

·                     1 Complete set of roll assemblies

·                     Manual Roll Adjustment

·                     Die Clamps

·                     Die & Roll Hoist

·                     Dump chute

·                     Automatic greasing system with 50kgs grease pump

·                     Sandblasted and painted

·                     Die Size I/D 762 mm x 156 mm Working Width

 

  

Fully Refurbished CPM 7932-9 complete with:                                                                                                         SOLD   

  •          New Quill Bearings
  •          New Mainshaft Bearing
  •          New Quill Wear Ring, Tapered Inserts, Deflector,              Wipers & Door Knives (2)
  •          All new seals & O Rings
  •          1 Set Roll Assemblies (2)
  •         New Die Clamps
  •          Manually Operated Die & Roll Hoist
  •          Manual Roll Adjustment
  •           Dump Chute                            
  •          Sandblasted and painted                                                                                                                                                                                              
  •          Die Size I/D 825 mm x 240 mm Working Width  (Die surface area 6,220 cm2)

 

 

Complete Pelleting Line Comprising of:

                      CPM 2016-3 pellet press with 55kw motor &                                         CPM force feederSOLD

•          CPM feeder, magnet & Ecoflow conditioner

•          Geelen VK0.9 x 0.9KL cooler with inlet rotary valve.

•          Sieve

•          Conveying system

 

 

 

Year 2000 Fully Refurbished CPM 3020-6 complete with:  SOLD                                                                                                                                                                                                                                      132 KW Motor 1480 rpm

•          1 Complete set of roll assemblies

•          Manually operated die & roller hoist

        Dump Chute

•          Manual Roll Adjustment 

•          Automatic greasing system

•          Sandblasted and painted 

•          Die Size I/D 508 mm x 156 mm Working Width

 


Factory Refurbished CPM 2016-4 (2000) complete with:

      

  •             90 Kw motor 1480 rpm
  •             1 Set Roll Assemblies
  •             Manual Roll Adjustment
  •             New Shearpin Assembly 
  •             New Main shaft              
  •             New main shaft disc                                              
  •             New Quill shaft
  •             New Die clamp assembly    
  •             New door
  •             New feed cone
  •             All new bearings                                  
  •             Dump chute
  •             Sandblasted and painted  
 
 
  

 

 

2004 Fully Refurbished CPM 7932-11 Oil Lubricated Mainshaft complete with:            

 

  •             315 Kw motor 1500 rpm
  •             1 Set Roll Assemblies
  •            Manual Roll Adjustment
  •             Shearpin Housing
  •             Roll Adjustment
  •             Manual Operated Die & Roll Hoist
  •            New Type Die Clamps
  •              Dump chute
  •              Latest CPM Oil Seal Arrangement
  •              50Kg or 200Kg Reservoir Greasing System  
  •              Sandblasted and painted
  •             Die Size I/D 825 mm x 270 mm Working Width (7,000 cm2 Die Surface Area)
 
  

 

2004 Fully Refurbished CPM 7930-4 Oil Lubricated Mainshaft complete with: 

 

  •             315 Kw motor 1500 rpm
  •             1 Set Roll Assemblies
  •             New Shearpin Housing
  •             Manual Roll Adjustment
  •             Pneumatic Die Hoist
  •            New Type Die Clamps
  •             Dump chute
  •             Latest CPM Oil Seal Arrangement
  •             50Kg or 200Kg Resevoir Greasing System  
  •             CPM Conditioner & Feeder (option) 
  •             Sandblasted and painted
  •             Die Size I/D 762 mm x 94 mm Working Width

 

  

 

Fully Refurbished CPM 3020-6 complete with:                                                SOLD 

              135 KW Motor 1480 rpm

•              1 Complete set of roll assemblies

•              Manually operated die & roller hoist

               CPM Force Feeder

•              Manual Roll Adjustment

•              Automatic greasing system

•              Sandblasted and painted

            Die Size I/D 508 mm x 156 mm Working Width

              Excellent Condition

 

 

Fully Refurbished CPM 7726-7 complete with:  

 SOLD

  •           200 Kw motor 1500 rpm
  •                 210RPM Die Speed
  •             1 Set Roll Assemblies
  •             Manual Roll Adjustment
  •             Die Hoist
  •             Die Clamps
  •             Dump chute
  •             Automatic Greasing System with Grease Pump 
  •             Sandblasted and painted
  •             Die Size I/D 673 mm x 181 mm Working Width                                 

                                                

Fully refurbished CPM 7930-8 complete with:                                                                                                                 SOLD

              250 KW Motor 1480 rpm

•              1 Complete set of roll assemblies

•              Manually operated die & roller hoist

•              Manual Roll Adjustment

•              Automatic greasing system

•              Sandblasted and painted

            Die Size I/D 762 mm x 210 mm Working Width

 

 

 

2000 Fully refurbished CPM 3020-6/5039/529 complete with:                                                                 SOLD

              135 KW Motor 1480 rpm

•              1 Complete set of roll assemblies

•              Manually operated die & roller hoist

•              Manual Roll Adjustment

•              Automatic greasing system

•              Sandblasted and painted

             Die Size I/D 508 mm x 156 mm                                              Working Width

 

                                                                 

Fully refurbished CPM 7730-8 complete with:                                                                                         SOLD

              200 KW Motor 1480 rpm

•              1 Complete set of roll assemblies

•              Manually operated die & roller hoist

•              Lineator Roll Adjustment

•              Automatic greasing system

•              Sandblasted and painted

            Die Size I/D 762 mm x 210 mm Working Width

 

Fully refurbished CPM 7800 Oil Lubricated Main Shaft  complete with:                                                     SOLD

 

  • 180 KW Motor 1500 rpm
  •  New Die Clamps
  • 1 Complete set of roll assemblies
  • Die Hoist
  • Manual Roll Adjustment
  • Dump chute
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size I/D 762 mm x 210 mm Working Width

Fully refurbished CPM 7930/8 Oil Lubricated Main Shaft complete with:                                               SOLD

  •             185 KW Motor 1500 rpm
  •             1 Complete set of roll assemblies
  •             New Die Clamps
  •             New Oil and Cooler System
  •             Manual Roll Adjustment
  •             Die Hoist
  •             Dump chute
  •             Automatic greasing system with 50kgs grease pump
  •             Sandblasted and painted
  •             Die Size I/D 762 mm x 210 mm Working Width

Fully Refurbished MillTec 165 Standard complete with:                                                      SOLD

·         160 Kw 1500 rpm motor

·         1 complete set roll assemblies

·         Manually operated die and roll hoist

·         Manual roll adjustment

·         Dump Chute

·         Automatic greasing system with 50kgs grease pump

·         Sandblasted and painted 

 ·         Die Size I/D 600 mm x 140 mm Working Width 

 

 

Fully refurbished Matador M6 complete with:                                                                                                                                                       

 

  • 110Kw Motor 1500rpm
  • New Die Clamps
  • New Feed Cone
  • 1 Complete set of roll assemblies (3)
  • Manual Roll Adjustment
  • Stainless steel door
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size I/D 408 mm x 116 mm Working Width

2005 Fully Refurbished CPM 7930-4 Oil Lubricated Mainshaft complete with:                                                   SOLD

  •             315 Kw motor 1500 rpm
  •     1 Set Roll Assemblies
  •             Manual Roll Adjustment
  •             Die Hoist
  •     Die Clamps
  •             Dump chute
  •             Automatic Greasing System with Grease Pump 
  •     CPM LL 733 Conditioner Feeder with 11Kw Motor
  •             Sandblasted and painted
  •             Die Size I/D 762 mm x 94 mm Working Width

Fully Refurbished CPM 7930-8 Press (choice of 3) complete with:                                                 SOLD

         250 Kw 1500 rpm motor

         1 complete set roll assemblies

         Manually operated die and roll hoist

         Manual roll adjustment

         Dump Chute

         Automatic greasing system with 50kgs grease pump

         Sandblasted and painted 

         Die Size I/D 762 mm x 210 mm Working Width 

 

 

Fully Refurbished Paladin 1200D with:                                                                                                                          SOLD

  

  • 2 x 90Kw 1500 rpm motors (not shown)
  • Dump chute
  • 1 complete set roll assemblies
  • Manual roll adjustment
  • Sandblasted and painted
  • Die size I/D 650 mm x 175 mm Working Width 
 
 

Fully refurbished CPM 7726-7 Grease Lubricated Main Shaft (choice of 2) complete with:                                                                                                                                                                SOLD                                 

  200 KW Motor 1500 rpm

 New Die Clamps

1 Complete set of roll assemblies

Die Hoist

Manual Roll Adjustment

Dump chute

Automatic greasing system with 50kgs grease pump

Sandblasted and painted

Die Size I/D 673 mm x 181 mm Working Width

 
 


Fully Refurbished CPM 7122 Oil Lubricated Main Shaft complete with:                              SOLD

·         160Kw 1500 rpm motor

·         1 complete set roll assemblies

·         Manually operated die and roll hoist

·         Manual roll adjustment

·         Dump Chute

·         Automatic greasing system with 50kgs grease pump

·         Sandblasted and painted 

·         Die Size I/D 572 mm x 158 mm Working Width 

 

 

 

1998 Fully refurbished CPM 3020-6/4776/518 Complete with:        SOLD

  • 110 KW Brook Hansen Motor 1480 rpm
  • 1 Complete set of roll assemblies
  • Manual Roll Adjustment
  • Die Hoist
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size I/D 508 mm x 156 mm Working Width 
  • Optional Extra: CPM Force Feeder 

Fully refurbished CPM 7000 Oil Lubricated Main Shaft  complete with:                                                             SOLD

  • 185 KW Motor 1500 rpm
  • New Quill Shaft
  •  New Die Clamps
  • 1 Complete set of roll assemblies
  • Die Hoist
  • Manual Roll Adjustment
  • Dump chute
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size I/D 572 mm x 158 mm Working Width

1983 Fully refurbished CPM 7122 Oil Lubricated Main Shaft (choice ofSOLD

  • 200 or 185KW Motor 1500 rpm
  • New Clamps
  • 1 Complete set of roll assemblies
  • Die Hoist
  • Manual Roll Adjustment
  • Dump chute
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size I/D 572 mm x 158 mm Working Width  


1989 Fully refurbished CPM 7722-6 / 3616 / 065  Grease Lubricated Main Shaft  complete with:                      SOLD

160 KW Motor 1500 rpm

New Die Clamps

1 Complete set of roll assemblies

Die Hoist

Manual Roll AdjustmentDump chute

Automatic greasing system with 50kgs grease pump

  Sandblasted and painted

  Die Size I/D 572 mm x 158 mm Working Width 

 

 

 

 

Kahl 33-390 complete with:                                                                                           SOLD 

      30 KW Motor 1475 rpm  

 

     Year of manufacture 1997           

 

     Die OD-390mm, track 75mm        

 

     1 4 x 30 die

 

     1 set of rolls

              


  
 
 

 CPM 2000 Press Complete with: 

 SOLD

         New mainshaft and mainshaft disc

         New front and back plates

         New pinion shaft

         Manual greasing system

         Die Size I/D 407.5 mm x 115.5 mm Working Width   

 

 

 

 

 

1994 Fully refurbished CPM 7730-7/4268/250) Grease Lubricated Mainshaft complete with:   SOLD  

  • 180 KW Motor 1500 rpm                                          
  • Complete set of roll assemblies                                                       
  • New Die Clamps
  • New Feed Cone
  • Die Hoist
  • Dump chute
  • Automatic greasing system with 50kgs grease pump
  • Manual Roll Adjustment
  • Sandblasted and painted
  • Die Size: I/D 762 mm x 180 mm Working Width


Converted to Oil Lubrication
Converted to Oil Lubrication

1993 Fully refurbished CPM 7722-6/3904/6 Grease Lubricated Mainshaft complete with:SOLD  

  •  160 KW Motor 1500 rpm  
  • Complete set of roll assemblies
  • Die Hoist
  • Manual Roll Adjustment
  • Dump chute
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size: I/D 572 mm x 158 mm Working Width

1987 Fully refurbished CPM 7000  Oil Lubricated Main Shaft complete with:SOLD                 

  • 160 Kw Motor 1500 rpm
  • 1 Complete set of roll assemblies
  • Die Hoist
  • Manual Roll Adjustment
  • Dump chute
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size: I/D 572 mm x 158 mm Working Width

 


1986 Fully refurbished CPM 7122/2 2492 / 162 Oil Lubricated Main Shaft complete with                                    SOLD

  • 160 KW Motor 1500 rpm
  • New Clamps
  • 1 Complete set of roll assemblies
  • Die Hoist
  • Manual Roll Adjustment
  • Dump chute
  • Automatic greasing system with 50kgs grease pump
  • Sandblasted and painted
  • Die Size I/D 572 mm x 158 mm Working Width




1997 Fully refurbished CPM 3020-6/4634/496 Complete with: SOLD 

130 KW Motor 1500 rpm

CPM Force Feeder

1 Complete set of roll assemblies

Die Hoist

Lineator Roll Adjustment

Automatic greasing system with 50kgs grease pump

Sandblasted and painted

Die Size I/D 508 mm x 156 mm Working Width  

 

    


 

More on way-Contact CFE for Latest List of Available Pellet Presses
 

All Pellet Presses are Fully Refurbished to a High Standard, Run in at Factory and Supplied with Warranty

Refurbished Paladin 1200
Refurbished Paladin 1200
 
 
 
 
 
 
 
 
 
 
Fully Refurbished CPM 2016
Fully Refurbished CPM 2016
Refurbished CPM 7722-6
Refurbished CPM 7722-6


Refurbished CPM 7726
Refurbished CPM 7726
Refurbished CPM 3000
Refurbished CPM 3000
Fully Refurbished Milltec 235W May 2013
Fully Refurbished Milltec 235W May 2013
T +353 66 71 42655
E info@cfegroup.com